Combination Wood Coffee Table
Posted June 14, 2013

 



Start with a Maple Slab...


A friend who was moving away gave me a slab of western bigleaf maple that he had brought over from the Seattle (wet) side of the state.  It was nicely figured, but was highly checked and twisted, my thinking initially that it was destined for our firewood bin.


Through some studious bandsaw work, I was able to salvage 4 nice, thick pieces for legs on a potential project.  As the length was limited on the slab, it would need to be a fairly short piece of furniture.  As it so happened, I was looking for a coffee table design with rather large legs, but still balanced that would work in an area of our home with a reddish terra-cotta tile floor.  Applying myself to SketchUp, I came up with a table plan to incorporate the maple legs, in combination with a darker wood to work with the floor tile.


Hand planing the maple legs reveled just how much figure was present in the wood and inspired me to try to find some comparable maple for the rails and aprons.  Having no more of the western maple, I settled on some eastern bird's eye maple as a suitable mate for the legs.


Legs
The side and back rails are mortised into the legs before being tapered.  The front bottom blade is also mortised into the front legs.  For this project, a little something different, as I cut all of the tenons with a table saw dado stack instead of the tenon jig.  This seems to be a real time saver and I'm quite pleased with the results. 

markingStret    glueup
The top stretcher is fitted with double dovetails into the top of the front legs, to add mechanical rigidity to the table.  I scribe the dovetails onto the leg tops with a knife and then rough-cut them out with a small router and finish cut them with a chisel.  After tapering the legs and mortising the back rail for the drawer dividers, the base is glued up.

markingStret    glueup
After initial glue up of the base, I added the drawer dividers, which are pieces of alder that have small pieces of maple biscuted to the front ends.  The dividers are attached to the back rail with mortise and tenons and sandwiched between the front lower blade and top stretcher.  A screw on the top and underside is added to ensure good pressure and alignment while the glue is setting.


glueup
I believe that drawer fronts of contrasting woods can add some pop to a piece, but careful consideration needs to be given to the selection of the two woods.  In my opinion, some woods seem to work a lot better than others when placed side-by-side.  Originally, I had planned to use some Pacific Madrone for the drawer fronts on this table, but found it not to contrast sufficiently with the maple.

markingStret    glueup
Usually, I'm not a big fan of working with tropical exotics -- wild & woolly grain can make for difficult planing and dust that can be hazardous to health-- are a couple of my cautions.  But having on hand some beautiful Bolivian Rosewood that I've been moving around for years, I decided to try it for some drawer fronts on this table.  I was able to choose a single piece in order to maintain continuous grain across all three drawer fronts.

markingStret    glueup
I had also planned to use some western alder for the drawer sides, but am still drawn to the hard crispness of maple for those pieces as well.  While a little more difficult to work with, I like the clean and contrasting dovetails that can be cut in the maple.  These half-blind dovetails on the drawer fronts were fashioned using the same techniques as in my cherry chest, that is, a combination of hand cut, bandsaw, and router to remove some of the waste.

markingStret    glueup
The drawers required only minor hand-planing of the sides and front to get a nice fit in their openings, as I'm finally getting good at building a drawer to fit from the beginning.  Having nice square openings and drawers certainly helps as well.  I did stay with the alder for the drawer bottoms, as it works well as a secondary wood for this purpose.


markingStret    glueup
Working with tropical hardwoods will inevitability lead to some scraper work, as the grain doesn't always respond perfectly to my planes.  These particular pieces of Rosewood have a certain rowed structure -- grain sloping in strips alternately one way and another.  They certainly meet Krenov's definition of an "unfriendly wood".  On the other hand, after gluing together some 5/4 hard maple for the table top, it is a true joy to plane, yielding nicely to my sharp smoother and producing perfect ribbons of microscopically thin silk.

markingStret    glueup
The top is made from solid 1 1/8" rock maple--not an easy slab of hardwood to manuver around.  The ends are breadboarded and pegged with square pieces of rosewood.  I also inserted rosewood splines into the outer intersection of the breadboard and top, both for affect and strength on the ends.

markingStret    glueup
I cut the spline on the end of the top to accept the breadboard end with a dado on the table saw and do the final thickness adjustment with a small rabbet plane.  After attaching the breadboard, holes for the square pegs are done with a 3/8" bit on the hollow chisel mortiser.

markingStret    glueup
Pegs are pounded into place through a groove in the dadoed top end that allows the breadboard end to move, as it will, depending on temperature and moisture throughout the year.  Grooves for the rosewood splines on the top sides are cut with a chisel.

markingStret    glueup
The bottom surface of the table top has a slight bevel on the sides and little larger bevel on the ends.  I rounded over the entire top-edge with a hand plane and sandpaper, adjusting the radius as I went to get the desired effect.

markingStret    glueup
For drawer knobs, I turned several styles using different woods, before deciding on ones made directly from the rosewood for the best fit.  Shown are knobs in cocobolo, rosewood, and ebony.

After applying several coats of wipe-on tung oil finish, sanding to about 400 grit between coats, the piece is complete.  This table ended up with 6 different species of wood:  western big-leaf maple (legs) eastern hard maple (top & drawer sides), bolivian rosewood(drawer fronts & knobs), western alder (drawer bottoms), Alaskan birch (drawer spacers) and persimmon (drawer slides).



  Back To Top                 Home
ChiselHead
  Sharing and Trying to be a Better Wood Worker
             Recent Projects

          
              Ash and Walnut Chairs

          
                  Walnut Hall Table

          
              Cherry Entry Bench

          
           Cherry Shinto Sideboard

          
           Table of Mexican Woods 

          
          Claro Walnut Writing Desk

            
              Shinto Cherry Cabinet

          
            Maple Cherry Huntboard

          
              Spalted Maple Cabinet

          
                 Maple Coffee Table

          
              Oak Drawer Bookcases

          
             Oak Mission Living Set

          
              Maple Kindling Box

          
                 Walnut BookCases

          
           Large Walnut DiningTable
  Contact Us:
            Jim & Rori Draper
             3004 Pleasant Valley Rd.
             Rice, WA. 99167

             Email:  jim@draperjim.com

  Copyright © 2017 Jim Draper